Sport ATV, UTV, Utility ATV — By ATV Mag on August 19, 2008 at 12:00 pm

A poor running ATV can be as frustrating as your in-laws crashing your humble abode for a week with your drunk, stumbling brother-in-law Ned in tote. Nobody wants to deal with Ned and his constant pestering. Worse yet, trying to make a quick escape from the burdensome in-laws on an ATV experiencing lack of power, off-idle stumbles and tough starting can be equally as humbling.
Since we can’t help you with your in-laws and Ned, who is sitting on your favorite recliner belching and scratching, we’ll cover an area of expertise we can aid you with: tuning your ATV’s carburetor for a clean escape next time the in-laws are in town. While we often refer to the carb as the heart of an ATV — it meters the flow of fuel and air — don’t let it intimidate you. Cleaning and tuning a carb is a task you should be able to handle if you have an ounce or two of technical skills. A few frosty 12-ounce beverages to keep Ned at bay wouldn’t hurt either.
If you don’t feel confident in your skills after reading this, have an experienced technician or friend walk you through the process or do the work for you. To coax them into helping, take away Ned’s beverages and offer them to said helper.
For this particular carburetor clean-up, we used a 2003 Honda Foreman Rubicon and its gummed-up 33.5mm Keihin CV carb. While carbs differ from model to model, the following instructions should give you a basis to start your service. If your ATV has a twin carbureted engine, you’ll obviously have to do this process twice. However, it’s important to note we advise you to avoid mixing parts between the two carbs, as each carb will have a slightly different construction that might not be easily identifiable to the naked eye.

Getting Started
If you are a neat freak, have a piece of cardboard on hand and slide it underneath your ATV before removing the carb. This will help you avoid cleaning up any gas spills or messing up a clean shop. Turn the fuel petcock to the off position and then ensure Ned isn’t looking over your shoulder cracking a cig. Next, locate the float bowl drain screw on the bottom of the carb and drain the fuel from the carburetor. Generally this screw is at the bottom of the float bowl and can be accessed by a screwdriver.
For our Honda, we removed the seat and the left and right side plastics, consisting of about five plastic grommets per side and one screw, to have enhanced access to the Keihin carb. Next, we removed the air intake and airbox to allow for more wiggle room when removing the carb. Procedure for your model will vary.
Now, before removing hoses from the carb, we grabbed the paint marker, scratch paper and pencil. We marked each hose and wire with a number and wrote down exactly where the number corresponded to on the carb. Most locations are intuitive, but this step will save you time during installation.
To free the carb from the assembly, we had to remove the air and fuel lines and two large hose clamps that connect the airbox to carb and carb to engine intake. Also, our 2003 Rubicon had two electrical connections that needed to be unplugged. Access to the throttle linkage required removal of a black plastic cover on the carb and one screw.
Stage I
For those of you who plan on doing a basic carb service, you might be able to remove the float bowl without removing the carb from the ATV. For that reason, we’ll start with our carb cleaning how-to at the float bowl as Stage I.
A float bowl filled with gasoline residue, rust and other small particles can often be blamed as the culprit for a rough idle and other maladies. Rotten fuel can dry up and form a thick goop in the float bowl if it has been sitting for extended periods of time. This goop invades the jets and causes all sorts of issues with the fuel/air mixture.
Locate the float bowl on the bottom of the carb and remove the four screws affixing the bowl to the carb with a tight-fitting screwdriver. If you are having issues breaking the screws loose, spray with WD-40 or Liquid Wrench and let the fluid work for 30 minutes or so to avoid stripping the screws — screw heads are generally fairly soft on carbs and are easily susceptible to stripping.
Once the bowl is removed, inspect the gasket for wear or rips. The gasket should protrude above the rim. If it doesn’t, it should be replaced. Now, for those of you who plan on soaking the carb in cleaner overnight, remove the main jet and main jet holder, slow jet, float and corresponding seat washer, fuel needle and fuel needle seat.
With the jets removed, it is a good time to inspect them for clogs and clean them. Soak the jets in carb cleaner. After letting them soak, grab a toothbrush and clean the jets with the soft bristles invading the tiny holes throughout the jets. It is important to use only a soft bristle brush. Wire or similar material can actually widen the holes and you will accidentally re-jet your ATV’s carb. Don’t be that guy! Leave that role to Ned.
If your carb’s float bowl has built-up residue and particles, you will want to soak it in the gallon can before cleaning. Our Rubicon’s bowl had a thick layer of goop built up that required a lengthy soaking period to break the goop loose and dissolve it. The Keihin carb’s float bowl had tough-to-reach crevices so we used compressed air to help blow out any of the gunk lingering in the bowl.
Stage II
If you plan on seeing this cleaning all the way through like Ned finishing that case of beer, this stage is for you. Our next step in the carb cleaning involves removing the diaphram and metering assembly. At the top of the carb, locate the circular cap retained by four screws. Remove the screws and carefully lift the cap off so as to not allow the spring underneath to shoot out uncontrollably.
Now, carefully remove the diaphram and metering assembly. To remove the metering needle, use a screw driver or nut driver to turn the plastic retainer and free the needle. Inspect the diaphram for wear or rips. Be careful with the diaphragm as this is one of the most expensive carb components. Before setting the diaphram down on your work bench, invert the diaphram so it looks like a mushroom. This prevents the diaphram from taking any unnecessary abuse while outside the carb. To clean the diaphragm assembly, spray cleaner on a shop rag and wipe off any varnish. Try to avoid spraying cleaner on the diaphragm as it is made from rubber and the abrasive cleaner can destroy it.
For our Honda Rubicon model, the carb comes with a primer. We removed the primer by backing out two screws. Also, ensure the O-ring seal isn’t damaged. The orifice directly inside the carb from the primer in our Rubicon had a significant amount of residue and goop. Cleaning the primer is an important step on this particular model because the priming action pushes residue through the carb network and can really impact performance.
Next, remove the choke assembly and idle adjustment assembly. Both are fairly easy to remove. To disassemble, remove the screw at the top of the plastic tube for each assembly. Once the screw is backed out, the tube can be pulled off the actuating shaft. Removing the choke plunger will be the most difficult task here, but it can be removed by lifting up while rotating the retaining fork.
Now, it’s time to call upon that ounce or two of technical skill you have. Removing the throttle shaft assembly can be a nerve-racking task, and many forgo it because removing the throttle plate can be difficult. We recommend removing the throttle plate and shaft if you plan on soaking the carb body in cleaner.
The plate can be removed by backing out the two Phillips screws that hold the plate in place. This is the most important step. The screws are staked, meaning the tips of the screws were widened so they keep a tight fit to the shaft. If you can’t find a tight-fitting screwdriver, avoid this step so you don’t strip out the screws — and use spray cleaner opposed to soaking. Before removing the plate, note the side facing out as this side must be facing out when you re-install it. If you do remove the plate, the shaft on our Keihin carb could be pulled out by removing a C-clip on the top of the shaft and then carefully removing the felt seal with a slotted screwdriver. While removing the shaft, note where all the springs and linkages go.
Now the carb body is ready to be soaked in cleaner. After the carb has rested in cleaner for about a half hour, the residue and particles should easily break free with compressed air, a rag and toothbrush. Q-tips can also be used to reach smaller crevices. Use the spray cleaner and hit all the orifices and crevices in the carb to remove any lingering particles.
With the cleaning complete, it’s time to reverse the process and install all the components back on the carb body. Ensure you don’t overtighten critical components like jets and the metering needle.
When the service is complete, you should have an easier starting, more responsive and powerful engine. You may be surprised by the power that returns – power you forgot your ATV had. It will be useful power too, for your getaway the next time Ned is in town.
Tools For The Job
You won’t need many tools or supplies for a carb service, but there are a few key things you should have on hand before starting the job.
• The most obvious is carb cleaner. Don’t skimp on generic or unknown brands. Ask around and find a cleaner that does a good job of breaking down and dissolving built-up residue quickly. We’ve had success with Gunk and B-12 Chemtool. You will want a spray carb cleaner and a gallon can to soak parts in overnight — if you plan on doing an in-depth cleaning. The gallon cans usually come with a metal bin that you can suspend parts in, as sediment will break up and fall to the bottom of the can. If you have access to a parts cleaner, even better.
• Soft bristle toothbrush. This is a helpful tool when cleaning jets and scrubbing interior portions of the carb.
• Several small plastic bins or cups to keep important parts separated.
• Compressed air. A can of compressed air will work if you don’t have access to an electric air compressor.
• Shop rags. Carb cleaner is a very abrasive chemical, so have a few rags on hand for any spills or oversprays that might come in contact with vital rubber components.
• Paint marker along with scratch paper and a pencil.
• Jets if considering re-jetting due to altitude or adding a performance exhaust system.

Events — By Release on November 23, 2009 at 10:11 am

The dates have changed from May 12-15th to April 21-24th, 2010. Mark your calendars and book your reservations quickly if you’re planning to attend. For those that have never been, it’s guaranteed to be the Ultimate Family Adventure Vacation!

This is the same weekend as the April Action Car Show, so book your accommodations quickly. For those looking to camp or RV, the OK RV Park (use 1UTVRally2) and the KOA are empty and would welcome your family’s reservation. But, if you’re looking to make your reservation at a hotel, I’d highly recommend booking your reservations ASAP because of the Car Show.

If you’ve never been to the UTV Rally before, this video shows you exactly what the UTV Rally is all about. If you have been before, there’s a good chance you’re in this video.

Click Here for the UTV Rally Video

Participant Registration?

Participant registration for the UTV Rally will be open shortly. We’ve moved the registration in-house this year to make it easier on your families to register plus easier on us at check-in at the Rally.

If you’re not registered on the UTV Rally forum already, please do so here: Click Here – Forum Registration  so you don’t miss any emails we send out.

Sponsor/Vendor Registration?

Sponsor/Vendor registration for the UTV Rally will be open shortly, as well.

If your company isn’t registered on the UTV Rally forum already, please do so here: Click Here – Forum Registration  so you don’t miss any emails we send out.

Sponsorship/Vendor Salespeople Needed

I’m looking to gather a small team of UTV enthusiasts to focus on increasing the number of vendors and sponsors at the UTV Rally this year. I’d prefer someone with knowledge of the industry that has existing relationships already established.

If you’re interested in finding out more about this opportunity, please email me at chris@utvrally.com. All details, UTV Rally contacts, commission %’s, etc will be discussed then.

Trail Guides Needed

If you’ve been to the UTV Rally before as a participant and feel confident leading or tailgunning folks on well mapped/marked trails in Moab, I’d welcome the opportunity to comp your registrations and have you help trail guide this year. Please email or call me at chris@utvrally.com or 602-568-3944.

If you’ve been a sponsor/vendor in previous years and would like to find out how being trail guides can drastically increase your company’s exposure, please contact me at chris@utvrally.com or 602-568-3944. Everyone’s help would be greatly appreciated!

Event Updates

We’ve been running Nationwide 60 second commercials on Dish Network’s Motorsports Mania TV channel 230: In Country Television – Motorsports Mania TV since October. These will be run till the event, which is huge exposure we’ve never done before. Plus, it will be Nationwide on Direct TV starting in January, as well. I think Wally even put up one of our previous shows he ran for us in the past on the website. Here’s the 60 second commercial: 60 Second UTV Rally Commercial.

This year we’re planning for exciting events for your kids. With the event being earlier than previous years, we’re hoping it’s easier for you to bring your children. We’re planning to host some of the most exciting kids events you’ve ever seen. So, if you want a night out on the town with your spouse, drop your kids off and go have some fun. Or, if you’d like to hit the hardcore trails one of the days, drop them off and take your 4-seater UTV wherever you’d like without having to worry about your kids in the back.

All in all, we’re hoping to see you and your families at the UTV Rally on April 21-24th, 2010. We’ll be sending out another email shortly when registration opens, and if you have any questions at all, please don’t hesitate to contact us.

BRP celebrates championships at NEATV-MX banquet

Manufacturer — By Release on December 2, 2009 at 12:37 pm

Valcourt, Québec, December 2, 2009 – At the New England ATV motocross year-end banquet in Massachusetts, nine Can-Am DS 450 riders were recognized for success throughout the 2009 season. Representatives from BRP were present at the event to thank those riders who earned contingency cash for podiums and four class championships during the course of the race season. It was a great night of celebration for not only the ATV racers, but everyone involved in the NEATV-MX organization.

In all, Can-Am DS 450 racers finished on the podium 103 times across six classes in the 12-round race series. That is not all, three DS 450 racers were able to finish the season on top of the points table and win class championships in the 30-Plus A, 25-Plus Open, Production B and 30 B/C classes. In all, BRP paid out more than $50,000 USD in contingency to racers in the NEATV-MX series for 2009.

The three racers winning championships were: Roy Lampron (30-Plus A and 25-Plus Open), Mark Gehring (Production B) and James Mondo (30-Plus B/C). Each of these three NEATV-MX champions took part in the Can-Am X-Team DS 450 EFI Amateur Racer Program through their local dealerships.

Can-Am has pledged to support the New England ATV MX series in 2010 with an extensive contingency cash program similar to this past race season, an announcement on the program is forthcoming. For more information on the NEATV-MX series and its 2010 schedule, continue to check www.neatv-mx.com for updates

DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">

• Home
• Customer Service
• Contact Us
• Subscribe
• RSS
• 
• RSS via email
• 

• ATVs
  • Utility
  • Sport
  • UTV
  • Manufacturer
    • Arctic Cat
    • Can-Am
    • Honda
    • Kawasaki
    • KTM
    • Kymco
    • Polaris
    • Suzuki
    • Yamaha
    • Other
  • Features
• News
  • Manufacturer
  • Product
  • Trail Access
  • Job Openings
  • Other
• Products
  • New Products
    • Riding Gear
    • Implements/Attachments
    • Tires/Wheels
    • Performance
    • Accessories
    • Other
  • Tested Products
    • Riding Gear
    • Implements/Attachments
    • Tires/Wheels
    • Performance
    • Accessories
    • Other
    • Project Quads
• How To
  • Utility ATV
  • Sport ATV
  • UTV
  • Ride Technique
  • Other
• Destinations
  • By Location
    • East
    • Midwest
    • West
    • International
    • South
• Racing
  • Motocross
  • Cross-Country
  • Mud
  • Other
  • Desert
• Events
• Photos
• Videos
• Blog
• Forums

First Test: KYMCO Maxxer 375 Crossover

Everybody loves an underdog story, and we’re sitting on a good one: KYMCO’s all-new Maxxer 375 sport-utility...

Full Test: Riding Yamaha’s New 2010 YFZ450X In The Woods

Although you can’t please all the people all the time, Yamaha is making every effort to do just that....

Hunting For Texas Pronghorn Aboard Yamahas

Jagged pinnacles and rolling parapets of the Davis Mountains rose from shimmering plains before us. Grumbling...

Inaugural SXS & ATV Roundup At Tennessee’s Brimstone

A crowd of more than 5,000 people attended the first SxS & ATV Roundup held Labor Day weekend at...

Headlines

• MIC To CPSC: Stop Ban On Youth ATVs, Motorcycles!
  

  January 13, 2010 7:43
• Polaris Unveils Awesome Four-Seat RZR!
  

  January 11, 2010 10:42
• Take Our Three-Minute Survey
  

  December 18, 2009 14:34
• 2010 North and South Challenge Announced
  

  December 16, 2009 7:56
• Winter Use Varies Across The Country
  

  December 10, 2009 15:52

>>> See More Headlines >>>

ATVs

See more ATVs >>

First Test: KYMCO Maxxer 375 Crossover

Everybody loves an underdog story, and we’re sitting on a good one: KYMCO’s all-new Maxxer 375 sport-utility crossover....

0

Jan 13, 2010 14:23

Racing

See more Racing >>

2010 WARNERT RACING / CAN-AM GNCC RACE TEAM ANNOUNCED

Valcourt, Québec– BRP is pleased to announce the roster of Team Warnert Racing / Can-Am, which will compete during the...

0

Jan 15, 2010 8:38

Products

See more Products >>

Trail Tested: Olympia Air Throttle Gloves, ATV Stuff Rack Mini-Cooler

OLYMPIA AIR THROTTLE GLOVES For more than 60 years, Olympia Sports Company has earned a reputation for high-quality, reasonably...

0

Dec 16, 2009 10:47

How To

See more How To >>

Planning A Great Day Ride

Riding off-road is an escape from the norm for ATV enthusiasts. It’s their chance to explore nature and put a smile on...

1

Aug 6, 2009 12:00

Recent Articles

Polaris Defense Enters Low Speed Vehicle Market

Minneapolis, January 6, 2010 – Polaris Defense today announced the introduction of their Low Speed Vehicle, the Polaris EV LSV, designed for on and off-road use. “We are excited to introduce the Polaris EV LSV to the military market,� said Mark McCormick, managing director of Polaris Defense. “The...

January 7th, 2010 | | Read More

Inaugural SXS & ATV Roundup At Tennessee’s Brimstone

A crowd of more than 5,000 people attended the first SxS & ATV Roundup held Labor Day weekend at Brimstone Recreation near Huntsville, Tennessee. ATV, side-by-side and dirt bike riders flocked to Brimstone, a 19,196-acre off-road paradise that is located in the northeast part of Tennessee and the...

December 31st, 2009 | | Read More

BRP celebrates championships at NEATV-MX banquet

Valcourt, Québec, December 2, 2009 – At the New England ATV motocross year-end banquet in Massachusetts, nine Can-Am DS 450 riders were recognized for success throughout the 2009 season. Representatives from BRP were present at the event to thank those riders who earned contingency cash for podiums...

December 2nd, 2009 | | Read More

4th Annual UTV Rally – April 21-24th

The dates have changed from May 12-15th to April 21-24th, 2010. Mark your calendars and book your reservations quickly if you’re planning to attend. For those that have never been, it’s guaranteed to be the Ultimate Family Adventure Vacation! This is the same weekend as the April Action Car...

November 23rd, 2009 | | Read More

Oklahoma Turkey Hunt

A rookie bags his first turkey The cold Oklahoma sky was pitch-black, with a steady, howling wind battering the trees and the recently charred prairie grass. Nobody said a word. With a delicate touch, our group of three quietly left our rides, gingerly loaded our shotguns with shells and began our silent...

November 23rd, 2009 | | Read More

SUZUKI CHAMPIONS TOUR CAPTURES 6 CHAMPIONSHIPS AT IMS Shows

BREA, CA (November 20, 2009) - In 2009, American Suzuki dominated racing by earning six major national championships from Superbike to Motocross to ATV. American Suzuki is proud to announce The Suzuki Champions Tour, a unique display designed to get Suzuki consumers up close and personal with the Championship...

November 20th, 2009 | | Read More

AMA urges support for language that would protect kids’ access to youth OHV’s

PICKERINGTON, Ohio — The American Motorcyclist Association (AMA) is urging all motorcyclists and ATV riders to ask their U.S. senators and representatives to support language in an appropriations bill that would allow kids’ dirtbikes and all-terrain vehicles (ATVs) to continue to be sold. The...

November 20th, 2009 | | Read More

ATV 360

Select Videos

Product Showcase

Photos


View more photos >

Related Sites

• ATV Magazine BLOG
• ATV Message Boards/Forums

  Local Guides

 Alabama
 Alaska
 Arizona
 Arkansas
 California
 Colorado
 Connecticut
 DC
 Delaware
 Florida
 Georgia
 Hawaii
 Idaho
 Illinois
 Indiana
 Iowa
 Kansas
 Kentucky
 Louisiana
 Maine
 Maryland
 Massachusetts
 Michigan
 Minnesota
 Mississippi
 Missouri
 Montana
 Nebraska
 Nevada
 New Hampshire
 New Jersey
 New Mexico
 New York
 North Carolina
 North Dakota
 Ohio
 Oklahoma
 Oregon
 Pennsylvania
 Rhode Island
 South Carolina
 South Dakota
 Tennessee
 Texas
 Utah
 Vermont
 Virginia
 Washington
 West Virginia
 Wisconsin
 Wyoming

Archives

Select Month January 2010 December 2009 November 2009 October 2009 September 2009 August 2009 July 2009 June 2009 May 2009 April 2009 March 2009 February 2009 January 2009 December 2008 November 2008 October 2008 September 2008 August 2008 July 2008 June 2008 May 2008 April 2008 March 2008 February 2008 January 2008 November 2007 September 2007 August 2007 July 2007 April 2007 March 2007 January 2007 December 2006 October 2006 August 2006 June 2006 April 2006 March 2006 January 2006 April 2005 November 2004 June 2004 April 2004

• Home
• Blog
• Forums
• Customer Service
• Contact Us
• Subscribe
• RSS
• 
• RSS via email
• 

   Copyright © ATV Magazine Online 2010. All Rights Reserved. · Privacy Policy updated 10-06-2009 · Site Terms & Conditions

Register for a trial subscription and you'll receive a Risk-Free Issue, no strings attached. If you like ATV Magazine, pay just $16.97 for 5 more issues (6 in all). Otherwise, write "cancel" on the bill, return it and owe nothing.

Email:
Name:
Address:
City:
State:
ZIP:

    For Canadian and International Orders, please order here.